992
992
Cat® Large Wheel Loaders set the standard for optimized productivity, minimizing downtime, enhancing operator comfort, and protecting people on your jobsite through key safety features.
Book a Demo
Explore my deals
Specifications
Axles
-
FrontFixed
-
RearTrunnion
-
Oscillation Angle±9°
Brakes
-
BrakesISO 3450:2011
Buckets
-
Bucket Capacities11.5-24.5 m³ (15-32 yd³)
Cooling System
-
Ambient Capability Hydraulically Driven Demand Fan - Standard109.4 °F 43 °C
-
Ambient Capability, Hydraulically Driven Demand Fan - High131 °F 55 °C
Dimensions - High Lift - Approximate
-
Tread Width10.83 ft 3302 mm
-
Rack Back Angle - Ground Level42.5 degrees
-
Dump Angle at Maximum Lift-48.1 degrees
-
Rack Back Angle - Maximum Lift56.2 degrees
-
Width - Over Tires - With Bulge14.75 ft 4495 mm
-
Rack Back Angle - Carry51.6 degrees
-
Ground to Top of Exhaust Stacks17 ft 5169 mm
-
Ground to Top of ROPS18.3 ft 5571 mm
-
Ground to Top of Hood13.1 ft 3983 mm
-
Ground to Center of Front Axle4.3 ft 1308 mm
-
Ground to Bumper Clearance3.8 ft 1145 mm
-
Ground to Lower Hitch Clearance2.2 ft 666 mm
-
Reach - Maximum Lift7.6 ft 2319 mm
-
Clearance at Maximum Lift17.2 ft 5256 mm
-
B-Pin Height - Maximum Lift24.5 ft 7465 mm
-
Maximum Overall Height - Bucket Raised32 ft 9759 mm
-
Rear Axle - Centerline to Bumper13.5 ft 4119 mm
-
Wheel Base19.3 ft 5890 mm
-
Maximum Overall Length51.6 ft 15733 mm
-
Front Axle Centerline to Bucket Tip18.8 ft 5724 mm
Dimensions - Standard Lift - Approximate
-
Ground to Top of Exhaust Stacks17 ft 5169 mm
-
Ground to Top of ROPS18.3 ft 5571 mm
-
Ground to Top of Hood13.1 ft 3983 mm
-
Ground to Center of Front Axle4.3 ft 1308 mm
-
Ground to Bumper Clearance3.8 ft 1145 mm
-
Ground to Lower Hitch Clearance2.2 ft 666 mm
-
Reach - Maximum Lift8.2 ft 2503 mm
-
Clearance at Maximum Lift15.2 ft 4630 mm
-
B-Pin Height - Maximum Lift22.8 ft 6948 mm
-
Maximum Overall Height - Bucket Raised30.8 ft 9390 mm
-
Rear Axle - Centerline to Bumper13.5 ft 4119 mm
-
Tread Width10.83 ft 3302 mm
-
Rack Back Angle - Maximum Lift56.9 degrees
-
Dump Angle at Maximum Lift-49.5 degrees
-
Rack Back Angle - Ground Level40.2 degrees
-
Width - Over Tires - With Bulge14.74 ft 4493 mm
-
Wheel Base19.3 ft 5890 mm
-
Rack Back Angle - Carry48.9 degrees
-
Maximum Overall Length50.8 ft 15489 mm
-
Front Axle Centerline to Bucket Tip18 ft 5480 mm
Engine
-
Net Power814 hp 607 kW
-
Engine ModelCat® C32B
-
EmissionsU.S. EPA Tier 4 Final, U.S. EPA Tier 2 Equivalent
-
Rated Speed1750 rpm
-
Gross Power - SAE J1995 at 1,750 rpm - Tier 4/HRC (Highly Regulated Country) - Standard900 hp 671 kW
-
Gross Power - SAE J1995 at 1,750 rpm - Tier 4/HRC - High Ambient937 hp 699 kW
-
Gross Power - SAE J1995 at 1,750 rpm - Tier 2/LRC (Less Regulated Country) - Standard907 hp 676 kW
-
Gross Power - SAE J1995 at 1,750 rpm - Tier 2/LRC - High Ambient944 hp 704 kW
-
Gross Power - ISO 14396 at 1,750 rpm - Tier 4/HRC - Standard884 hp 659 kW
-
Gross Power - ISO 14396 at 1,750 rpm - Tier 4/HRC - High Ambient921 hp 687 kW
-
Gross Power - ISO 14396 at 1,750 rpm - Tier 2/LRC - Standard893 hp 666 kW
-
Gross Power - ISO 14396 at 1,750 rpm - Tier 2/LRC - High Ambient931 hp 694 kW
-
Net Power - SAE J1349 at 1,750 rpm - Tier 4/HRC - Standard814 hp 607 kW
-
Net Power - SAE J1349 at 1,750 rpm - Tier 4/HRC - High Ambient814 hp 607 kW
-
Net Power - SAE J1349 at 1,750 rpm - Tier 2/LRC - Standard823 hp 614 kW
-
Net Power - SAE J1349 at 1,750 rpm - Tier 2/LRC - High Ambient823 hp 614 kW
-
Bore5.7 in 145 mm
-
Stroke6.4 in 162 mm
-
Displacement1963.5 in³ 32.1 l
-
Peak Torque - SAE J1995 - Tier 4/HRC - Standard @ 1,200 rpm3514 ft·lbf 4765 N·m
-
Peak Torque - SAE J1995 - Tier 4/HRC - High Ambient @ 1,300 rpm3555 ft·lbf 4820 N·m
-
Peak Torque - SAE J1995 - Tier 2/LRC - Standard @ 1,200 rpm3537 ft·lbf 4796 N·m
-
Peak Torque - SAE J1995 - Tier 2/LRC - High Ambient @ 1,350 rpm3570 ft·lbf 4841 N·m
Hydraulic Cycle Times
-
Rack Back2.3 s 2.3 s
-
Rack Back - High Lift2.3 s 2.3 s
-
Raise9 s 9 s
-
Raise - High Lift9 s 9 s
-
Dump2.6 s 2.6 s
-
Dump - High Lift2.6 s 2.6 s
-
Float Down3.2 s 3.2 s
-
Float Down - High Lift3.2 s 3.2 s
-
Total Hydraulic Cycle Time17.1 s 17.1 s
Hydraulic System - Lift/Tilt
-
Lift/Tilt System - CircuitPositive Flow Control
-
Lift/Tilt System - PumpVariable Displacement Piston
-
Maximum Flow at 2,165 rpm250 gal/min 950 l/min
-
Relief Valve Setting - Lift/Tilt5000 psi 34500 kPa
-
Lift Cylinder - Bore9.3 in 235 mm
-
Lift Cylinder - Stroke63.5 in 1613 mm
-
Tilt Cylinder - Bore11.5 in 292 mm
-
Tilt Cylinder - Stroke41.5 in 1055 mm
Hydraulic System - Steering
-
Steering System - CircuitPilot, Load Sensing
-
Steering System - PumpPiston, Variable Displacement
-
Maximum Flow at 1,400-1,850 rpm70 gal/min 265 l/min
-
Steering Cut Off Pressure4500 psi 31000 kPa
-
Total Steering Angle80°
-
Steering Cycle Times - Low Idle4.9 s 4.9 s
-
Steering Cycle Times - High Idle3.1 s 3.1 s
Operating Specifications
-
Operating Weight233430 lb 105882 kg
-
Rated Payload - Standard25.5 ton (US) 23.1 t
-
Rated Payload - Standard (Material Handler)30 ton (US) 27.2 t
-
Rated Payload - High Lift22.5 ton (US) 20.4 t
-
Rated Payload - High Lift (Material Handler)27 ton (US) 24.5 t
-
Bucket Capacity Range11.5-24.5 m³ (15-32 yd³)
-
Cat Truck Match - Standard775/777
-
Cat Truck Match - High Lift785
Service Refill Capacities
-
Fuel Tank385.7 gal (US) 1460 l
-
Cooling Systems59.4 gal (US) 225 l
-
Crankcase31.7 gal (US) 120 l
-
Transmission51.5 gal (US) 195 l
-
Differential - Final Drives - Front96.4 gal (US) 365 l
-
Differential - Final Drives - Rear96.4 gal (US) 365 l
-
Hydraulic System Factory Fill (Implement)104.1 gal (US) 394 l
-
Hydraulic Tank - Implement60.2 gal (US) 228 l
-
Hydraulic Factory Fill (Steering)32.5 gal (US) 123 l
-
Hydraulic Tank (Steering Tank Only)26.3 gal (US) 99.5 l
Sound Performance - Standard
-
NoteMachine Sound Level (ISO 6396:2008) - 116 dB(A)
Sound Performance - Suppression
-
NoteMachine Sound Level (ISO 6396:2008) - 113 dB(A)
Transmission
-
Transmission TypeCat Planetary Powershift
-
Forward - 14.3 mile/h 7 km/h
-
Forward - 27.4 mile/h 11.9 km/h
-
Forward - 312.7 mile/h 20.5 km/h
-
Direct Drive - Forward 1Disabled
-
Direct Drive - Forward 28 mile/h 12.9 km/h
-
Direct Drive - Forward 314 mile/h 22.6 km/h
-
Reverse - 14.7 mile/h 7.5 km/h
-
Reverse - 28.1 mile/h 13 km/h
-
Reverse - 313.9 mile/h 22.4 km/h
-
Direct Drive - Reverse 15 mile/h 8 km/h
-
Direct Drive - Reverse 28.8 mile/h 14.2 km/h
-
Direct Drive - Reverse 315.3 mile/h 24.7 km/h
Benefits
SAFETY
- Designed for visibility, with a taller windshield that provides a 25% increase in glass surface area for a better view to the bucket, standard rear-view camera, optional Detect 270-degree cameras, standard LED lighting and mining mirrors.
- Improved access and egress, with integrated powered access system, adjustable hanging steps, 45-degree-angle wide stairs, emergency egress ladder, and full handrails on each side.
- Wide walkways with non-skid surfaces and integrated lockout/tagout points designed into the service areas.
- Speed limiter, which sets the maximum speeds in both forward and reverse.
OPERATOR COMFORT
- 50% increase in leg room and increased width by the operator’s knees compared to previous model.
- Reduced vibration, low sound levels and automatic temperature controls.
- Electro-hydraulic speed-sensing steering with force feedback for shift-long comfort.
- Pressurized cab featuring Next Gen Seat with 9-inch travel, active cooling and heating, adjustable lumbar support, seat cushion tilt adjustment, and air-adjustable bolsters on the seat and backrest.
CONFIDENT & EMPOWERED OPERATORS
- Low-effort integrated controls that make cycles smoother and faster while reducing fatigue.
- Large, easy-to-read, color LED displays that provide access to the Electronic Operation & Maintenance Manual.
- Operator coaching, which helps empower operators to exceed targets by measuring and providing feedback to reinforce proper operating techniques.
- New Autodig Components that boost efficiency and reduce tire wear by automating critical parts of the digging cycle.
- Payload Overload Prevention, which inhibits severe payloads from being raised to full truck height.
PRODUCTIVITY
- Increased rated payload, which allows for a a 4-pass match to a 90.7-tonne (100-ton) truck in all applications.
- Better digging thanks to 20% more breakout force compared to previous models, with no increase in cycle time; 9.5% boost in rimpull; and increased traction.
- Superior loading with Cat Performance Series Buckets, which deliver easier, faster loading; increased fill factors and material retention; larger bucket volume; and better bucket and machine stability due to the payload being lower and closer to the machine.
- Greater stability, thanks to an increase in static tipping load and greater tipping-to-weight ratio, which helps operators be more confident and productive.
EFFICIENCY-BOOSTING FEATURES
- Tire Slip Prevention, which reduces rimpull when there is less downforce on the tire and increases rimpull when there is more downforce on the tire — providing maximum rimpull when you can use it.
- Tire Set, which automatically applies a lift command at the optimal time to increase traction on the tire, allowing for an increase in usable rimpull.
- Lift Stall Prevention, which automatically applies the impeller clutch when necessary to prevent hydraulic stall when lifting up through the face — keeping the lift motion continuous, without excessive use of the impeller clutch.
- Positive Flow Control Hydraulic System, which boosts efficiency with concurrent pump and valve control and increases bucket feel and control to deliver consistent performance.
- On-demand throttle feature that allows operators to maintain normal operation with the left pedal and implements while the 992 manages the engine speed.
SERVICEABILITY
- Reduced time spent on regular maintenance procedures thanks to features such as ground-level or platform access to filters; grouped service points; swing-out doors on both sides of the engine compartment; improved access for engine and pump drive service as well as to cooling package; and automatic lubrication system that greases the linkage, hitch, steering and axle trunnion bearings.
- Relocated service station that provides easy access to functions such as coolant and oil as well as level indicators; Cat battery charging connector; and indicator lights for full fuel tanks.
- Standard VIMS™ monitoring system that delivers critical health and payload information, keeping performance at optimum levels and allowing advanced troubleshooting and planning to lower maintenance costs.
- Improved hydraulic system filtration as well as prognostics for the implement pump and remaining useful life of the engine air filter.
- Remote Flash capabilities that reduce downtime by providing immediate access to the latest software updates.
VERSATILITY
- Ideal for all temperatures, with high ambient package for operation in temperatures as high as 55 degrees C / 131 degrees F; and cold-weather features such as cooling fan bypass; 120V or 240V coolant heating elements and fuel heater; 240V engine oil; and heated mirrors.
- Approved for higher payloads in low to moderate digging resistance applications; increased payload intended for rehandled material in the ROM pad area or stockpile material, such as coal.
- Variety of bucket options, including limestone bucket; granite buckets for use in high-abrasion production applications; heavy-duty rock buckets for applications like face loading tightly compacted pit materials or handling materials of moderate abrasion and high impact; coal buckets for light density non-abrasive materials; and iron ore buckets for extremely aggressive applications.
- New Performance Series Buckets that feature extended floor, dual radius and angled side bars for fast loading; larger bottom box section for increased strength, high fill factors and good material retention; and taller side plate with a level top surface improves operator visibility to the bucket from the cab.
- Cat Ground Engaging Tools (GET) that feature CapSure™ Retention Technology, which simplifies component replacement with hammerless retention for fast, easy and safe installation.
DURABILITY
- New C32B engine improved for increased durability.
- Use of structural castings at the high-stress locations where the lift arm and front axle mount; and improvements to the axle cutout, upper hitch design and rear trunnion mounting.
- Loads efficiently transmitted by the field-proven solid steel lift arms and reinforced pin joint bores.
- Powertrain improvements including 20% increase in Planned Component Replacement interval of drivetrain components; increase in axle housing size, which enabled the elimination of the brake anchor and integration of brakes into the housing; 23% increase in oscillation joint diameter, which greatly increases surface area and reduces bearing wear; and increased hardness on Output Transfer Gears (OTG).
- Frame, powertrain, engine and components that all built to be rebuilt — using new, remanufactured or rebuilt parts and components — to deliver multiple lives of like-new performance at a fraction-of-new price.
TECHNOLOGY
- Cat MineStar™ Terrain for loading, which provides real-time feedback on payloads and design plan progress to increases productivity and accuracy, reduce rework, enhance ore control and improve shift-to-shift operator performance.
- MineStar Object Detection, which combines radar and camera systems to warn operators about light vehicles or stationary hazards within the immediate vicinity of their machines.
- MineStar Health, which delivers critical event-based machine condition and operating data and includes comprehensive equipment health and asset monitoring capabilities, with a wide range of diagnostic, analytic and reporting tools.
- Upgraded touchscreen information display that provides intuitive operation and easy navigation and keeps operators informed about machine systems to decrease service time.
- Cat ProductLink™, which provides remote access to information on machine systems and diagnostic codes; allows you to track utilization, fuel usage and payload summaries; and gives access to machine location, service meter hours and reporting status.
SUSTAINABILITY
- Designed to be more efficient and use less fuel, which reduces engine emissions and carbon footprint; Tier 4 Final engine reduces NOx and particulate matter.
- Engine Idle Shutdown, which saves fuel by making it possible to avoid unnecessary idling.
- Better control of fluids through use of Cat anti-drain filter housings and component ecology drains.
- Retrofits and upgrades for older machines — to incorporate efficiency improvements and emission reductions, and to keep them in production longer to conserve energy and minimize the need for raw materials
- Cat Rebuild and Cat Reman programs, which preserve raw materials, conserve energy and reduce emissions.
Equipment Info
POWER TRAIN
Engine, C32B
LINKAGE
Standard lift (23 tonnes/25.5 tons face, 27.2 tonnes/30 tons loose)
EFFICIENCY
Variable displacement implement pumps
ELECTRICAL AND LIGHTING
150-amp alternator
OPERATOR ENVIRONMENT
Premium seat with heated and actively cooled leather, adjustable lumbar support, air adjustable bolsters on the seat and backrest, seat cushion tilt adjustment and two-way thigh support adjustment
SAFETY
Ground-access ladders
MACHINE CONTROL AND GUIDANCE
MineStar Health ready
MineStar GUIDE ready
MineStar Edge ready
MineStar GUIDE ready
MineStar Edge ready
COOLING
Standard ambient package (recommended for site conditions that do not exceed 43° C [110° F])
SERVICE
Ground-level service center including:
– Implement and cooling fan oil level indicator
– Steering and brake oil level indicator
– Window washer fluid level indicator
– Transmission oil level indicator
– Fuel level indicator
– Engine oil level indicator
– Engine coolant level indicator
– Automatic lubrication system grease tank level indicator
– Starter lockout and LED
– Heavy-duty battery disconnect switch
– Stairway light switch
– Service lighting switch (if equipped)
– Fuel shutoff engine shutdown switch
– Engine oil fast-fill port
– Transmission oil fast-fill port
– Steering and brake hydraulic oil fast-fill port
– Steering and brake hydraulic oil drain port
– Engine coolant fast-fill port
– Implement and cooling fan hydraulic oil fast-fill port
– Implement and cooling fan hydraulic oil drain port
– Automatic lubrication system grease tank fill port
– 24V jump-start receptacle
– 12V power port
– 120V jacket water plug (if equipped)
– 240V jacket water plug (if equipped)
– VIMS key switch
– 14-pin service port
– Transmission lockout and LED
– Implement and cooling fan oil level indicator
– Steering and brake oil level indicator
– Window washer fluid level indicator
– Transmission oil level indicator
– Fuel level indicator
– Engine oil level indicator
– Engine coolant level indicator
– Automatic lubrication system grease tank level indicator
– Starter lockout and LED
– Heavy-duty battery disconnect switch
– Stairway light switch
– Service lighting switch (if equipped)
– Fuel shutoff engine shutdown switch
– Engine oil fast-fill port
– Transmission oil fast-fill port
– Steering and brake hydraulic oil fast-fill port
– Steering and brake hydraulic oil drain port
– Engine coolant fast-fill port
– Implement and cooling fan hydraulic oil fast-fill port
– Implement and cooling fan hydraulic oil drain port
– Automatic lubrication system grease tank fill port
– 24V jump-start receptacle
– 12V power port
– 120V jacket water plug (if equipped)
– 240V jacket water plug (if equipped)
– VIMS key switch
– 14-pin service port
– Transmission lockout and LED