906
906
Cat® Compact Wheel Loaders deliver high performance, versatility, and precision in any application.
Book a Demo
Explore my deals
Specifications
Axles
-
FrontFixed (standard) Locking Differential (optional)
-
RearFixed (standard) Locking Differential (optional)
-
NoteOscillation of ±11 degrees via hitch between front and rear frames.
Buckets
-
Bucket Capacities0.75-1.55 m³ (1.0-2.0 yd³)
-
Bucket Capacities - General Purpose0.80-1.35 m³ (1.0-1.7 yd³)
-
Bucket Capacities - Light Material1.25-1.55 m³ (1.6-2.0 yd³)
-
Multi-Purpose0.75-1.1 m³ (1.0-1.4 yd³)
-
NoteBucket selection must be made with an understanding of the material density and application to ensure machine stability is maintained within the tipping loads stated per model and configuration.
-
Note (1)Bucket capacities stated include BOCE, in line with ISO 7546.
Cab
-
ROPSISO 3471:2008
-
FOPSISO 3449:2005 Level II
-
Note (1)Canopy and cab, Rollover Protective Structures (ROPS) are available worldwide. Canopy not available in EU.
Dimensions - With HPL-V Coupler - Approximate#
-
Height: Ground to Cab**8.08 ft 2468 mm
-
Height: Ground to Beacon**8.67 ft 2651 mm
-
Height: Ground Axle Center**1.58 ft 480 mm
-
Height: Ground Clearance**1 ft 300 mm
-
Length: Overall*17.58 ft 5369 mm
-
Length: Rear Axle to Bumper4.58 ft 1391 mm
-
Length: Hitch to Front Axle3.58 ft 1085 mm
-
Length: Wheel Base7.08 ft 2170 mm
-
Clearance: Bucket at 45° *8.25 ft 2510 mm
-
Clearance: Load over Height**9.5 ft 2902 mm
-
Clearance: Level Bucket**9.92 ft 3037 mm
-
Height: Bucket Pin**10.67 ft 3251 mm
-
Height: Overall**13.5 ft 4122 mm
-
Reach: Bucket at 45° *2.42 ft 725 mm
-
Carry Height: Bucket Pin1.08 ft 321 mm
-
Dig Depth**0.33 ft 113 mm
-
Width: Bucket6.17 ft 1890 mm
-
Width: Tread Center4.67 ft 1420 mm
-
Turning Radius: Over Bucket14.17 ft 4327 mm
-
Width: Over Tires6.08 ft 1848 mm
-
Turning Radius: Outside of Tires12.92 ft 3925 mm
-
Turning Radius: Inside of Tires6.75 ft 2057 mm
-
Rack Angle at Full Lift56°
-
Dump Angle at Full Lift45°
-
Rack Angle at Carry51°
-
Departure Angle - Degrees30°
-
Articulation Angle - Degrees39°
-
Operating Weight: Bucket?^12632 lb 5730 kg
-
Tipping Load - Straight - ISO 14397-1?†9760 lb 4427 kg
-
Tipping Load - Full Turn - ISO 14397-1?†8225 lb 3731 kg
-
Operating Weight: Carriage and Tines?^^12240 lb 5552 kg
-
Tipping Load - Straight?†7748 lb 3514 kg
-
80% of Tip: Firm and Level EN474-3?††5211 lb 2364 kg
-
Note (1)*Vary with bucket
-
Note (2)**Vary with tire
-
Note (3)^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), 0.95 m3 (1.2 yd3) general purpose bucket.
-
Note (4)^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class II carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center).
-
Note (5)†Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing.
-
Note (6)††Full compliance to EN474-3 and SAE J1197.
-
Note (7)#HPL-A weight, tipping and rated loads are within 1% of the HPL-V.
-
Note (8)Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9EM 405/70 R18 tires and 0.95 m3 (1.2 yd3) general purpose bucket with bolt-on cutting edge or a class II fork carriage and tines (tire supplier variability can impact dimensions by 2%).
-
Note (9)Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9.
-
Length: Front Axle to Front of Coupler3.5 ft 1065 mm
-
Tipping Load - Full Turn?†6514 lb 2955 kg
Dimensions - With SSL Coupler - Approximate
-
Height - Ground to Cab8.08 ft 2468 mm
-
Height: Ground to Beacon**8.67 ft 2651 mm
-
Height: Ground Axle Center**1.58 ft 480 mm
-
Height - Ground Clearance1 ft 300 mm
-
Length - Overall with Bucket18.17 ft 5527 mm
-
Length: Rear Axle to Bumper4.58 ft 1391 mm
-
Length: Hitch to Front Axle3.58 ft 1085 mm
-
Length - Wheel Base7.08 ft 2170 mm
-
Clearance - Bucket at 45°7.83 ft 2391 mm
-
Clearance: Load over Height**9.5 ft 2902 mm
-
Clearance - Level Bucket9.92 ft 3028 mm
-
Height - Bucket Pin10.67 ft 3251 mm
-
Height: Overall**13.83 ft 4212 mm
-
Reach - Bucket at 45°2.67 ft 814 mm
-
Carry Height: Bucket Pin1.17 ft 345 mm
-
Dig Depth0.25 ft 85 mm
-
Width - Bucket6.17 ft 1890 mm
-
Width - Tread Center4.67 ft 1420 mm
-
Turning Radius - Over Bucket14.67 ft 4478 mm
-
Width - Over Tires6.07 ft 1848 mm
-
Turning Radius: Outside of Tires12.92 ft 3925 mm
-
Turning Radius - Inside Tire6.75 ft 2057 mm
-
Rack Angle at Full Lift51°
-
Dump Angle at Full Lift50°
-
Rack Angle at Carry46°
-
Departure Angle - Degrees30°
-
Articulation Angle - Degrees39°
-
Operating Weight: Bucket?^12863 lb 5835 kg
-
Tipping Load – Straight – ISO 14397-1?†8613 lb 3907 kg
-
Tipping Load – Full Turn – ISO 14397-1?†7220 lb 3275 kg
-
Operating Weight: Carriage and Tines?^^12434 lb 5640 kg
-
Tipping Load - Straight?†7359 lb 3338 kg
-
80% of Tip: Firm and Level EN474-3?††4970 lb 2254 kg
-
Note (1)*Vary with bucket
-
Note (2)**Vary with tire
-
Note (3)^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), 0.95 m3 (1.2 yd3) general purpose bucket.
-
Note (4)^^Horizontal Pin Lock Coupler (HPL-V) or Vertical Pin Coupler (SSL), class II carriage, 1220 mm (4 ft) tines (500 mm [20 in] load center).
-
Note (5)†Full compliance to ISO 14397-1 (2007) Sections 1 thru 6 (fork 500 mm [20 in] load center), which requires 2% verification between calculation and testing.
-
Note (6)††Full compliance to EN474-3 and SAE J1197.
-
Note (7)#HPL-A weight, tipping and rated loads are within 1% of the HPL-V.
-
Note (8)Dimensions listed are for a machine configured with standard cab, heater, 20 km/h (12 mph), standard guarding, 80 kg (176 lb) operator, full fluids, SPT9EM 405/70 R18 tires and 0.95 m3 (1.2 yd3) general purpose bucket with bolt-on cutting edge or a class II fork carriage and tines (tire supplier variability can impact dimensions by 2%).
-
Note (9)Note: Goodyear POWERLOAD® tires can add up to approximately 140 kg (305 lb) to the full turn tip load and reduce vertical height by approximately 25 mm (1 in) compared to SPT9.
-
Tipping Load - Full Turn?†2818 kg 6212 lb
-
Length: Front Axle to Front of Coupler4.33 ft 1316 mm
Engine
-
Maximum Gross Power74.7 hp 55.7 kW
-
Engine ModelCat C2.8*
-
Maximum Engine Speed2550 rpm
-
Maximum Gross Power - Rated Engine Speed2400 r/min 2400 r/min
-
Maximum Gross Power - SAE J199574.7 hp 55.7 kW
-
Maximum Gross Power - ISO 1439674.3 hp 55.4 kW
-
Maximum Gross Power - ISO 14396 (metric)75.3 mhp 75.3 mhp
-
Rated Net Power - Rated Engine Speed2400 r/min 2400 r/min
-
Rated Net Power - SAE J134972.7 hp 54.2 kW
-
Rated Net Power - ISO 924972.1 hp 53.8 kW
-
Rated Net Power - 2,400 rpm - ISO 9249 (metric)73.1 mhp 73.1 mhp
-
Maximum Gross Torque - SAE J1995222 lb/ft 300 N·m
-
Maximum Gross Torque - ISO 14396221 lb/ft 300 N·m
-
Maximum Net Torque - SAE J1349218 lb/ft 296 N·m
-
Maximum Net Torque - ISO 9249217 lb/ft 295 N·m
-
Displacement171 in³ 2.8 l
-
Bore3.54 in 90 mm
-
Stroke4.33 in 110 mm
-
NoteAdvertised power is tested per the specified standard in effect at the time of manufacture.
-
Note (1)Net power advertised is the power available at the flywheel.
-
Note (2)*Two Cat C2.8 engine emission options are available: 1) Meets U.S. EPA Tier 4 Final, EU Stage V. 2) U.S. EPA Tier 3 and EU Stage IIIA equivalent. Tier 3 engine specs are 0.3 kW/0.4 hp more gross power (SAE J1995), 0.2 kW/0.3 hp on net power (SAE J1349) and 1 N·m/0.7 lb-ft higher on gross torque (SAE J1995).
-
Note (3)#Maximum gross and net torque measured at 1,600 rpm.
Loader Hydraulic System
-
Main Relief - 1st Auxiliary (3rd slice)3408 psi 23500 kPa
-
Main Relief - 1st Auxiliary (3rd slice) - Standard Flow*21 gal/min 80 l/min
-
Main Relief - 1st Auxiliary (3rd slice) - High Flow*32 gal/min 120 l/min
-
Main Relief - 2nd Auxiliary (4th slice)3408 psi 23500 kPa
-
Main Relief - 2nd Auxiliary (4th slice) - Flow12 gal/min 45 l/min
-
Hydraulic Cycle Time - Rackback2.2 s 2.2 s
-
Hydraulic Cycle Time - Lift5 s 5 s
-
Hydraulic Cycle Time - Dump1.6 s 1.6 s
-
Hydraulic Cycle Time - Float Down2.8 s 2.8 s
-
Note* Maximum flow stated, actual flow delta could be 6% from data shown. Also adjustable from 20% to 100% of maximum flow through display.
Service Refill Capacities
-
Fuel Tank18.5 Gal 70 l
-
Cooling System3.2 Gal 12 l
-
Engine Crankcase2.3 Gal 8.8 l
-
Axles - Front Center Differential2.3 Gal 8.8 l
-
Axles - Rear Center Differential2.3 Gal 8.8 l
-
Hydraulic System - Including Tank17.8 Gal 67.5 l
-
Hydraulic Tank11.8 Gal 44.6 l
-
Transmission0.6 Gal 2.4 l
-
NoteNo Diesel Exhaust Fluid (DEF) fluid needed on this size engine.
Steering
-
Steering Articulation Angle - Each Direction39 ° 39 °
-
Maximum Flow - Steering Pump12.3 gal/min 46.7 l/min
-
Maximum Working Pressure - Steering Pump3336 psi 23000 kPa
-
Steering Cycle Times – (full left to full right) – at High Idle2.8 s 2.8 s
-
Number of Steering Wheel Turns - Full Left to Full Right or Full Right to Full Left3.25 turns or 4.00 turns
Sustainability
-
Recyclability93%
Tires
-
Tire Size - Standard*405/70 R18 SPT9
-
Tire Size - Optional405/70 R18 Powerloads
-
Tire Size - Optional (1)340/80 R18 XMCL/Bibload
-
Tire Size - Optional (2)340/80 R18 TRI 2
-
Tire Size - Optional (3)40X14-20 TL, SM/TR
-
Tire Size - Optional 4340/80 R18 Duraforce
-
Note*This tire has been used for all dimension, stability and performance data.
-
Note (1)Other tire choices are available. Contact your Cat dealer for details.
-
Note (2)In certain applications, the loader’s productive capabilities may exceed the tire’s tonnes-km/h (ton-mph) capabilities.
-
Note (3)Caterpillar recommends that you consult a tire supplier to evaluate all conditions before selecting a tire model.
Transmission
-
Forward and Reverse - Speed Range Creep#6 mile/h 10 km/h
-
Forward and Reverse - Speed Range 1*6 mile/h 10 km/h
-
Forward and Reverse - Speed Range 2** - High Speed10.5 mile/h 17 km/h
-
Forward and Reverse - Speed Range 2** - Standard12 mile/h 20 km/h
-
Forward and Reverse - Speed Range 3***25 mile/h 40 km/h
-
Note#Factory default shown, can be adjusted to any speed up to 19 km/h (12 mph).
-
Note (1)*Creep function not available in this gear or above.
-
Note (2)**Max speed dependent on model and configuration (standard vs. high speed transmission).
-
Note (3)***Reverse is 30 km/h (19 mph).
Weights
-
Operating Weight12628 lb 5730 kg
Benefits
CONFIGURED FOR SUCCESS
- Cat® wheel loaders set the standard for productivity, fuel efficiency and operator comfort. The Cat 906 Compact Wheel Loader has a high torque C2.8 engine that works in conjunction with an intelligent hystat power train to deliver exceptional fuel efficiency. Dependent on regional requirements our engines meet U.S. EPA Tier 4 Final and EU Stage V emission standards with a clean emission module designed to manage itself so you can concentrate on the task at hand or emit equivalent to U.S. EPA Tier 3 and EU Stage IIIA.
ENJOY ALL DAY COMFORT
- All new cab is spacious, quiet and comfortable with all around 360° visibility to keep you productive throughout the day. Seat-mounted controls feature a multifunction joystick for lift and tilt functions with an integrated thumb operated speed range, forward/neutral/reverse (FNR) switch, trigger operated differential lock and constant flow. Optional fourth function joystick also available.
- Digital display with soft touch buttons for customized settings to easily control linkage and drive train to further enhance operator comfort and safety.
EFFICIENTLY POWERFUL
- Cat C2.8 engine provides a cleaner, quieter operation while delivering superior performance and durability through a high torque, low speed design. Caterpillar’s exclusive Intelligent Power Management system monitors operator input and available power to keep the machine working at peak efficiency.
- “Shift on the go” locking differentials and hydrostatic transmission provide smooth and powerful operation while increasing the efficiency of machine cycles. New Powertrain (Utility) Mode via the display enables right pedal machine operation giving further improved operator controllability of attachment RPM versus machine ground speed over creep control and inching pedal.
WORK MADE EASY
- All-in-one joystick to keep eyes on the work while maximizing operation of hydro-mechanical attachments with a state of the art pressure compensated electro-hydraulic system. Optimized Z-bar linkage for great performance and versatility with buckets that now have the DNA of the larger Cat loaders, such as curved side plates and a flat torque tube for parallel reference to the cutting edge.
CUSTOMIZE YOUR EXPERIENCE
- Work as one with your machine by customizing the controls. Operator can adjust machine responsiveness with the push of a button based on the attachment or application. Once customized, settings can be locked with “simplified mode” to ensure the machine is consistent and intuitive for every user.
- Machine security is enhanced with a standard keycode or optional Bluetooth® technology.
PURPOSE BUILT SPECIALTY MODELS
- Machines can be built to meet industry and application specific needs: Agriculture, General Construction, Industrial and Waste, Landscaping or Snow Removal.
- The 906 is availble with the following specific handler arrangements: Ag Handler and Waste Handler
AFTERMARKET AND SERVICES
- Range of services and aftermarket retrofits and upgrades available to keep your machine going and configured for your application.
- Service and maintenance parts available, including a range of self-service options (SSO) and dealer installed kits.
- Integrated Technology available to reduce service costs and maintenance.
SUSTAINABILITY
- The Cat® C2.8 engine meets U.S. EPA Tier 4 Final and EU Stage V emission standards.
- Engine Idle Shutdown Timer reduces fuel burn, greenhouse gas emissions and unnecessary idle time by shutting down the machine after a pre-set idling period.
- Remote Troubleshoot decreases maintenance time and keeps your machine running with maximum efficiency by allowing your Cat dealer to virtually test the machine while working. Once a problem is identified, a technician can fix it the first time, saving time and money.
- Remote Flash minimizes downtime and maintenance time while keeping your asset running with maximum efficiency. Alerts for machine updates are sent virtually from your Cat dealer and updates can be deployed without a dealer technician needing to be onsite.
- Advanced Electro Hydraulic System provides the optimum balance of power and efficiency while giving you the control you need for your precise jobsite requirements.
- Engine Demand Fan is hydraulically driven to provide machine cooling only when needed, improving fuel efficiency and reducing greenhouse gas emissions.
- Hydrostatic Transmission is an efficient way to transfer engine power to the wheels at low speeds versus a torque converter.
- Efficient HVAC regulates temperature control. No need to leave the machine running to cool the cab.
- Shift on the go transmission, means no need to stop so you keep your momentum.
Equipment Info
ELECTRICAL
Product Link™
HYDRAULICS
Motor, single drive with dedicated implement and steering pumps
OPERATOR ENVIRONMENT
Cab
– Doors (2), fixed glass
– Wipers, front and rear, full front coverage
– Windshield, front single piece
– Window, rear heated
– Radio ready, speakers and wiring
– Air vents, (4) screen, (7) directional
– Heating, mechanical control unit
– Sun visor, solid, front full width
– Interior light (incandescent)
– Doors (2), fixed glass
– Wipers, front and rear, full front coverage
– Windshield, front single piece
– Window, rear heated
– Radio ready, speakers and wiring
– Air vents, (4) screen, (7) directional
– Heating, mechanical control unit
– Sun visor, solid, front full width
– Interior light (incandescent)
OTHER
Scheduled Oil Sampling (S·O·S?) ports, engine oil and hydraulic oil
POWER TRAIN
Fuel pump, priming (manual)/water separator/drain
Product Brochures